Abstract: Large steel silos are typical kinds of thin-walled structure which are widely used for storing huge quantities of granular solids in industry and agriculture. In the present analyses, the buckling design of large steel silos subject to Eurocode-specified solid pressure is demonstrated. The finite element model is established using the commercial general purpose computer package ANSYS. Six types of buckling analyses are carried out for the geometrically perfect and imperfect models with and without consideration of material plasticity. The load cases of concentric discharge, discharge patch load, large eccentricity discharge, and large eccentricity filling are considered. The buckling behavior of six example steel silos with capacities of 30 000–60 000 m³ is investigated. The silos’ slenderness ranges from 4.77 to 0.35, comprising very slender, slender, intermediate slender, squat, and retaining silos. The index called the ratio of capacity to steel consumption (RCS) is initially defined in the paper, which provides an effective measure for the economical design of steel silos. It is validated that the RCS index increases rapidly with the decrease of silo slenderness, and the storage efficiency of steel silo improved greatly as the slenderness changes from slender silo to retaining silo. The effects of patch load reveal that the buckling modes in the case of discharge patch load are very different from those of silos under concentric solid pressure, and the effect is unfavorable for buckling resistance of all levels of slenderness of the example silos, but contributes a small decrease to the RCS index (less than 10%). The buckling deformations from both the linear and nonlinear buckling analyses in large eccentric discharge are strongly asymmetrical arising from the circumferential and meridional non-uniform distribution of the solid pressures. The buckling is mainly governed by the non-uniform distribution of the solid pressure other than other influential factors such as the weld imperfection, geometrical and material nonlinearity, compared with the load case of concentric discharge. The RCS index of example silos under large eccentric discharge is reduced substantially, and is approximately half that of silos under concentric discharge. The linear and nonlinear buckling deformations in large eccentric filling are also asymmetrical, deviating from the center to the side where the most friction locates to the highest wall contact. The RCS index of example silos under large eccentric filling is also reduced substantially, and is approximately 70% that of silos under concentric discharge. This reveals that the large eccentricity both in discharging and filling could result in a strong decrease of storage efficiency of steel silos.

多种长细比的大型钢筒仓结构的屈曲设计

[1]ANSYS, 2008. ANSYS User’s Manual. Swanson Analysis Systems Inc., Houston, USA.

[2]BSI (British Standards Institution), 2002a. Basis of Structural Design, BS EN 1990:2002. BSI, UK.

[3]BSI (British Standards Institution), 2002b. Actions on Structures-Part 1-1: General Actions–Densities, Self-weight, Imposed Loads for Buildings, BS EN 1991-1-1:2002. BSI, UK.

[4]BSI (British Standards Institution), 2005. Design of Steel Structures-Part 1-1: General Rules and Rules for Buildings, BS EN 1993-1-1:2005. BSI, UK.

[5]BSI (British Standards Institution), 2006. Actions on Structures-Part 4: Silos and Tanks, BS EN 1991-4:2006. BSI, UK.

[6]BSI (British Standards Institution), 2007a. Design of Steel Structures-Part 1-6: Strength and Stability of Shell Structures, BS EN 1993-1-6:2007. BSI, UK.

[7]BSI (British Standards Institution), 2007b. Design of Steel Structures-Part 4-1: Silos, BS EN 1993-4-1:2007. BSI, UK.

[8]Gillie, M., Rotter, J.M., 2002. The effects of patch loads on thin-walled steel silos. Thin-Walled Structures, 40(10):835-852.

[9]Gillie, M., Holst, J.M.F.G., 2003. Structural behaviour of silos supported on discrete, eccentric brackets. Journal of Constructional Steel Research, 59(7):887-910.

[10]Greiner, R., Guggenberger, W., 1998. Buckling behaviour of axially loaded steel cylinders on local supports-with and without internal pressure. Thin-Walled Structures, 31(1-3):159-167.

[11]ISO (International Organization for Standardization), 1995. Basis for Design of Structures-Loads Due to Bulk Materials, ISO 11697:1995. ISO.

[12]Iwicki, P., Tejchman, J., Chroscielewski, J., 2014. Dynamic FE simulations of buckling process in thin-walled cylindrical metal silos. Thin-Walled Structures, 84:344-359.

[13]Kim, S.E., Kim, C.S., 2002. Buckling strength of the cylindrical shell and tank subjected to axially compressive loads. Thin-Walled Structures, 40(4):329-353.

[14]Li, B.R., Wang, X.Y., Ge, H.L., et al., 2005. Study on applicability of modal analysis of thin finite length cylindrical shells using wave propagation approach. Journal of Zhejiang University-SCIENCE A, 6(10):1122-1127.

[15]Pircher, M., Bridge, R.Q., 2001. Buckling and post-buckling behaviour of silos and tanks under axial load-some new aspects. Journal of Structural Engineering, 127(10):1129-1136.

[16]Rotter, J.M., Teng, J.G., 1989. Elastic stability of cylindrical shells with weld depressions. Journal of Structural Engineering, 115(5):1244-1263.

[17]Rotter, J.M., Zhang, Q., 1990. Elastic buckling of imperfect cylinders containing granular solids. Journal of Structural Engineering, 116(8):2253-2271.

[18]Sadowski, A.J., Rotter, J.M., 2011a. Buckling of very slender metal silos under eccentric discharge. Engineering Structures, 33(3):1187-1194.

[19]Sadowski, A.J., Rotter, J.M., 2011b. Steel silos with different aspect ratios-I: behaviour under concentric discharge. Journal of Constructional Steel Research, 67(10):1537-1544.

[20]Sadowski, A.J., Rotter, J.M., 2011c. Steel silos with different aspect ratios-II: behaviour under eccentric discharge. Journal of Constructional Steel Research, 67(10):1545-1553.

[21]Sadowski, A.J., Rotter, J.M., 2012. Structural behavior of thin-walled metal silos subject to different flow channel sizes under eccentric discharge pressures. Journal of Structural Engineering, 138(7):922-931.

[22]Sadowski, A.J., Rotter, J.M., 2013. Buckling in eccentrically discharged silos and the assumed pressure distribution. Journal of Engineering Mechanics, 139(7):858-867.

[23]Song, C.Y., 2002. Buckling of un-stiffened cylindrical shell under non-uniform axial compressive stress. Journal of Zhejiang University-SCIENCE, 3(5):520-531.

[24]Song, C.Y., 2004. Effects of patch loads on structural behavior of circular flat-bottomed steel silos. Thin-Walled Structures, 42(11):1519-1542.

[25]Song, C.Y., Teng, J.G., 2003. Buckling of circular steel silos subject to code-specified eccentric discharge pressures. Engineering Structures, 25(11):1397-1417.

[26]Standards Australia, 1996. Loads on Bulk Solids Containers, AS 3774-1996. Standards Australia, Sydney, Australia.

[27]Zhao, Y., Cao, Q.S., Xie, X.Y., 2006. Floating-roof steel tanks under harmonic settlement: FE parametric study and design criterion. Journal of Zhejiang University-SCIENCE A, 7(3):398-406.